Ninja ===== Introduction ------------ Ninja is yet another build system. It takes as input a file describing interdependencies of files (typically source code and output executables) and orchestrates building them, _quickly_. Ninja joins a sea of other build systems. Its distinguishing goal is to be fast. It is born from my work on the Chromium browser project, which has well over 20,000 source files and whose other build systems (including one built from custom non-recursive Makefiles) take tens of seconds to rebuild after changing one file, even on a fast computer. Here are some of the design goals of Ninja: * very fast (i.e., instant) incremental builds, even for very large projects. * very little implicit policy; "explicit is better than implicit". * get dependencies correct, and in particular situations that are difficult to get right with Makefiles (e.g. outputs should have an implicit dependency on the command line used to generate them; using gcc's `-M` flags for header dependencies). * when convenience and speed are in conflict, prefer speed. Some explicit _non-goals_: * convenient syntax for writing build files by hand. _You should generate your ninja files using another program_. This is how we sidestep many policy decisions. * built-in rules. _Out of the box, ninja has no rules for e.g. compiling C code._ * build-time customization of the build. _Options belong in the program that generates the ninja files_. To restate, Ninja manages to be simpler and faster than other build systems by being much more stupid. It has no built-in behavior describing how to build C source, or build libraries, or install binaries. You instead decide this policy when you create your project's `.ninja` files. Customization and configuration are out of scope; instead you should provide customization in the system that generates your `.ninja` files, like how autoconf provides `./configure`. Getting started --------------- The included `bootstrap.sh` should hopefully produce a working `ninja` binary, by first blindly compiling all non-test files together then re-building ninja using itself. Usage is currently just ---------------- ninja target ---------------- where `target` is a known output described by `build.ninja` in the current directory. Creating .ninja files ~~~~~~~~~~~~~~~~~~~~~ A build file (default name: `build.ninja`) provides a list of _rules_ along with a list of _build_ statements saying how to build files using the rules. The only other syntax is a way of declaring (immutable) variables. Conceptually, `build` statements describe the dependency graph of your project, while `rule` statements describe how to generate the files along a given edge of the graph. Here's a basic `.ninja` file that demonstrates most of the syntax. --------------------------------- cflags = -Wall rule cc command = gcc $cflags -c $in -o $out build foo.o: cc foo.c --------------------------------- Rules ~~~~~ Rules begin with a line consisting of the `rule` keyword and a name for the rule. Then follows an indented set of `key = value` lines. The basic example above declares a new rule named `cc`, along with the command to run. (In the context of a rule, the `command` key is special and defines the command to run. A full list of special keys is provided in the reference.) Variables begin with a `$` and are described more fully later, but here `$in` expands to the list of input files (`foo.c`) and `$out` to the output file (`foo.o`) for the command. Build statements ~~~~~~~~~~~~~~~~ Build statements begin with the `build` keyword, and have the format +build _outputs_: _rulename_ _inputs_+. Such a declaration says that all of the output files are derived from the input files. When the output files are missing or when the inputs change, ninja will run the rule to regenerate the outputs. The basic example above describes how to build `foo.o`, using the `cc` rule. A build statement may be followed by an indented set of `key = value` pairs, much like a rule. These bindings will shadow any bindings when evaluating the variables in the command. For example: ---------------- cflags = -Wall -Werror rule cc command = gcc $cflags -c $in -o $out # If left unspecified, builds get the outer $cflags. build foo.o: cc foo.c # But you can can shadow variables like cflags for a particular build. build special.o: cc.special.c cflags = -Wall ---------------- In the scope of a `build` block (including in the evaluation of its associated `rule`), the variable `$in` is the list of inputs and the variable `$out` is the list of outputs. If you need anything more complicated than this (for example, the basename of the first input), pass that in as an extra variable, like how `cflags` is passed above. Variables ~~~~~~~~~ Despite the non-goal of being convenient to write by hand, to keep build files readable (debuggable), Ninja supports declaring bindings (variables). A declaration like the following ---------------- cflags = -g ---------------- Can be used on the right side of an equals sign like this: ---------------- rule cc command = gcc $cflags -c $in -o $out ---------------- Variables can also be referenced using curly braces like `${in}`. Variables might better be called "bindings", in that a given variable cannot be changed, only shadowed. Within a larger Ninja project, different _scopes_ allow variable values to be overridden. XXX finish describing scopes. Ninja file reference -------------------- A file is a series of declarations. A declaration can be one of: 1. A rule declaration, which begins with +rule _rulename_+. 2. A build edge, which looks like +build _outputs_: _rulename_ _inputs_+ 3. Variable declarations, which look like +_variable_ = _value_+. 4. References to more files, which look like +subninja _path_+. Comments begin with `#` and extend to the end of the line. Newlines are significant, but they can be escaped by putting a `\` before them. Whitespace is only significant if it's at the beginning of a line. If a line is intended more than the previous one, it's considered part of its parent's scope; if it is indented less than the previous one, it closes the previous scope. Rule variables ~~~~~~~~~~~~~~ A `rule` block contains a list of `key = value` declarations that affect the processing of the rule. Here is a full list of special keys. `command` (_required_):: the command line to run. `depfile`:: path to an optional `Makefile` that contains _implicit dependencies_. Implicit dependencies are inputs to a build that are not given on the command line; the best example is how `gcc` has the `-M` family of flags to output the list of headers a given `.c` file depends on. + ---- rule cc depfile = $out.d command = gcc -MMD -MF $out.d [other gcc flags here] ---- `description`:: a short description of the command, used to pretty-print the command as it's running. The `-v` flag controls whether to print the full command or its description; if a command fails, the full command line will always be printed before the command's output. Evaluation and scoping ~~~~~~~~~~~~~~~~~~~~~~ XXX talk about where variables live, nested scopes etc