1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
|
<!--
Copyright (c) 2001, 2002, 2003 Steven Knight
Permission is hereby granted, free of charge, to any person obtaining
a copy of this software and associated documentation files (the
"Software"), to deal in the Software without restriction, including
without limitation the rights to use, copy, modify, merge, publish,
distribute, sublicense, and/or sell copies of the Software, and to
permit persons to whom the Software is furnished to do so, subject to
the following conditions:
The above copyright notice and this permission notice shall be included
in all copies or substantial portions of the Software.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY
KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE
LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION
OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION
WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
-->
<!--
=head1 Why Cons? Why not Make?
Cons is a B<make> replacement. In the following paragraphs, we look at a few
of the undesirable characteristics of make, and typical build environments
based on make, that motivated the development of Cons.
=head2 Build complexity
Traditional make-based systems of any size tend to become quite complex. The
original make utility and its derivatives have contributed to this tendency
in a number of ways. Make is not good at dealing with systems that are
spread over multiple directories. Various work-arounds are used to overcome
this difficulty; the usual choice is for make to invoke itself recursively
for each sub-directory of a build. This leads to complicated code, in which
it is often unclear how a variable is set, or what effect the setting of a
variable will have on the build as a whole. The make scripting language has
gradually been extended to provide more possibilities, but these have
largely served to clutter an already overextended language. Often, builds
are done in multiple passes in order to provide appropriate products from
one directory to another directory. This represents a further increase in
build complexity.
=head2 Build reproducibility
The bane of all makes has always been the correct handling of
dependencies. Most often, an attempt is made to do a reasonable job of
dependencies within a single directory, but no serious attempt is made to do
the job between directories. Even when dependencies are working correctly,
make's reliance on a simple time stamp comparison to determine whether a
file is out of date with respect to its dependents is not, in general,
adequate for determining when a file should be rederived. If an external
library, for example, is rebuilt and then ``snapped'' into place, the
timestamps on its newly created files may well be earlier than the last
local build, since it was built before it became visible.
=head2 Variant builds
Make provides only limited facilities for handling variant builds. With the
proliferation of hardware platforms and the need for debuggable
vs. optimized code, the ability to easily create these variants is
essential. More importantly, if variants are created, it is important to
either be able to separate the variants or to be able to reproduce the
original or variant at will. With make it is very difficult to separate the
builds into multiple build directories, separate from the source. And if
this technique isn't used, it's also virtually impossible to guarantee at
any given time which variant is present in the tree, without resorting to a
complete rebuild.
=head2 Repositories
Make provides only limited support for building software from code that
exists in a central repository directory structure. The VPATH feature of
GNU make (and some other make implementations) is intended to provide this,
but doesn't work as expected: it changes the path of target file to the
VPATH name too early in its analysis, and therefore searches for all
dependencies in the VPATH directory. To ensure correct development builds,
it is important to be able to create a file in a local build directory and
have any files in a code repository (a VPATH directory, in make terms) that
depend on the local file get rebuilt properly. This isn't possible with
VPATH, without coding a lot of complex repository knowledge directly into
the makefiles.
-->
<para>
XXX
</para>
<section>
<title>Differences Between &Make; and &SCons;</title>
<para>
XXX
</para>
</section>
<section>
<title>Advantages of &SCons; Over &Make;</title>
<para>
XXX
</para>
</section>
|
