[svn-r26747] updates to install_parallel.

1 files changed, 1 insertions, 118 deletions

diff --git a/release_docs/INSTALL_parallel b/release_docs/INSTALL_parallel
index 2624b3b..c38c3fc 100644
--- a/release_docs/INSTALL_parallel
+++ b/release_docs/INSTALL_parallel
@@ -107,89 +107,9 @@ This allows for >2GB sized files on Linux systems and is only available with
 Linux kernels 2.4 and greater.
 
 
-2.4. Red Storm (Cray XT3) (for v1.8 and later)
+2.4. Hopper (Cray XE6) (for v1.8 and later)
 -------------------------
-Both serial and parallel HDF5 are supported in Red Storm.
 
-2.4.1 Building serial HDF5 for Red Storm
-------------------------------------------
-The following steps are for building the serial HDF5 for the Red Storm
-compute nodes.  They would probably work for other Cray XT3 systems but have
-not been verified.
-
-# Assume you already have a copy of HDF5 source code in directory `hdf5' and
-# want to install the binary in directory `/project/hdf5/hdf5'.
-
-$ cd hdf5
-$ bin/yodconfigure configure
-$ env RUNSERIAL="yod -sz 1" \
-    CC=cc FC=ftn CXX=CC \
-    ./configure --prefix=/project/hdf5/hdf5
-$ make
-$ make check
-
-# if all is well, install the binary.
-$ make install
-
-2.4.2 Building parallel HDF5 for Red Storm
-------------------------------------------
-The following steps are for building the Parallel HDF5 for the Red Storm
-compute nodes.  They would probably work for other Cray XT3 systems but have
-not been verified.
-
-# Assume you already have a copy of HDF5 source code in directory `hdf5' and
-# want to install the binary in directory `/project/hdf5/phdf5'.  You also
-# have done the proper setup to have mpicc and mpif90 as the compiler commands.
-
-$ cd hdf5
-$ bin/yodconfigure configure
-$ env RUNSERIAL="yod -sz 1" RUNPARALLEL="yod -sz 3" \
-    CC=cc FC=ftn \
-    ./configure --enable-parallel --prefix=/project/hdf5/phdf5
-$ make
-$ make check
-
-# if all is well, install the binary.
-$ make install
-
-2.4.3 Red Storm known problems
-------------------------------
-For Red Storm, a Cray XT3 system, the yod command sometimes gives the
-message,  "yod allocation delayed for node recovery".  This interferes with
-test suites that do not expect seeing this message.  To bypass this problem,
-I launch the executables with a command shell script called "myyod" which
-consists of the following lines.  (You should set $RUNSERIAL and $RUNPARALLEL
-to use myyod instead of yod.)
-==== myyod =======
-#!/bin/sh
-# sleep 2 seconds to allow time for the node recovery else it pops the
-# message,
-#   yod allocation delayed for node recovery
-sleep 2
-yod $*
-==== end of myyod =======
-
-For Red Storm, a Cray XT3 system, the tools/h5ls/testh5ls.sh will fail on
-the test "Testing h5ls -w80 -r -g tgroup.h5" fails.  This test is
-expected to fail and exit with a non-zero code but the yod command does
-not propagate the exit code of the executables. Yod always returns 0 if it
-can launch the executable.  The test suite shell expects a non-zero for
-this particular test, therefore it concludes the test has failed when it
-receives 0 from yod.  To bypass this problem for now, change the following
-lines in the tools/h5ls/testh5ls.sh.
-======== Original =========
-# The following combination of arguments is expected to return an error message
-# and return value 1
-TOOLTEST tgroup-1.ls 1 -w80 -r -g tgroup.h5
-======== Skip the test =========
-echo SKIP TOOLTEST tgroup-1.ls 1 -w80 -r -g tgroup.h5
-======== end of bypass ========
-
-2.5. Hopper (Cray XE6) (for v1.8 and later)
--------------------------
-
-2.5.1 Building HDF5 for Hopper
------------------------------------------- 
 The following steps are for building HDF5 for the Hopper compute
 nodes.  They would probably work for other Cray systems but have
 not been verified.
@@ -226,43 +146,6 @@ The build will be in build-hdf5/hdf5/ (or whatever you specify in --prefix).
 To compile other HDF5 applications use the wrappers created by the build (build-hdf5/hdf5/bin/h5pcc or h5fc)
 
 
-2.5.2 Hopper known issues
-------------------------------
-Issue 1:
-Sometimes when building the library with make, you might get this problem:
-
-LD_LIBRARY_PATH="$LD_LIBRARY_PATH`echo | \
-sed -e 's/-L/:/g' -e 's/
-//g'`" \
-./H5make_libsettings > H5lib_settings.c
-|| \
-(test $HDF5_Make_Ignore && echo "*** Error ignored")
-|| \
-(rm -f H5lib_settings.c ; exit 1)
-/bin/sh: line 4: 9644 Segmentation fault
-LD_LIBRARY_PATH="$LD_LIBRARY_PATH`echo | sed -e 's/-L/:/g' -e 's/
-//g'`" ./H5make_libsettings > H5lib_settings.c
-
-If that happens, you are probable running with make -j <x>. In that
-case, you need to cleanup everything and start again as detailed above
-but use serial make (do not use -j <x>).
-
-Issue 2:
-* When building using the Cray compilers on Cray machines, HDF5
-  configure mistakenly thinks the compiler is an intel compiler and
-  sets the -std=c99 flag which breaks configure on Cray. To build HDF5
-  properly on a Cray machine, please consult with the instructions in
-  INSTALL_parallel for building on Hopper.
-  (MSC - 2013/04/26 - HDFFV-8429)
-
-Issue 3:
-* On hopper, the build failed when RUNSERIAL and RUNPARALLEL are set
-  to aprun -np X, because the H5lib_settings.c file was not generated
-  properly. Not setting those environment variables works, because
-  configure was able to automatically detect that it's a Cray system
-  and used the proper launch commands when necessary. 
-  (MSC - 2012/04/18)
-
 3. Detail explanation
 ---------------------