diff options
Diffstat (limited to 'bin/snapshot')
| -rwxr-xr-x | bin/snapshot | 516 |
1 files changed, 0 insertions, 516 deletions
diff --git a/bin/snapshot b/bin/snapshot deleted file mode 100755 index b4adf5e..0000000 --- a/bin/snapshot +++ /dev/null @@ -1,516 +0,0 @@ -#!/bin/sh -# -# Copyright by The HDF Group. -# Copyright by the Board of Trustees of the University of Illinois. -# All rights reserved. -# -# This file is part of HDF5. The full HDF5 copyright notice, including -# terms governing use, modification, and redistribution, is contained in -# the files COPYING and Copyright.html. COPYING can be found at the root -# of the source code distribution tree; Copyright.html can be found at the -# root level of an installed copy of the electronic HDF5 document set and -# is linked from the top-level documents page. It can also be found at -# http://hdfgroup.org/HDF5/doc/Copyright.html. If you do not have -# access to either file, you may request a copy from help@hdfgroup.org. - -# This script should be run nightly from cron. It checks out hdf5 -# from the source repository and compares it against the previous -# snapshot. If anything significant changed then a new snapshot is -# created, the minor version number is incremented, and the change is -# checked back into the source repository. -# - -# function definitions -TIMESTAMP() -{ - echo "=====" "$1": "`date`" "=====" -} - -EXIT_BANNER() -{ -TIMESTAMP "Exit $PROGNAME with status=$?" -} - -# Show current total disk usage. -DISKUSAGE() -{ - du -ks | \ - ( read x y; echo "Disk Usage=$x KB" ) -} - - -# MAIN -# SGI /bin/sh replaces $0 as function name if used in a function. -# Set the name here to avoid that ambiguity and better style too. -PROGNAME=$0 - -echo "=====================================" -echo "$PROGNAME $*" -echo "=====================================" -TIMESTAMP MAIN -uname -a - -# setup exit banner message -trap EXIT_BANNER 0 - -# Dump environment variables before option parsing -echo ===Dumping environment variables before option parsing === -printenv | sort -echo ===Done Dumping environment variables before option parsing === - -# snapshots release directory. Default relative to $BASEDIR. -ReleaseDir_default=release_dir - -# Where is the zlib library? -# At NCSA, half of the machines have it in /usr/lib, the other half at -# /usr/ncsa/lib. Leave it unset. -ZLIB_default= -ZLIB=$ZLIB_default - -# What compression methods to use? (md5 does checksum). -METHODS="gzip zip bzip2 md5 doc" - -# Use User's MAKE if set. Else use generic make. -MAKE=${MAKE:-make} - -# Default check action. -CHECKVAL=check - -# -# Command options -cmd="all" -test_opt="" -errcode=0 -while [ $# -gt 0 ] ; do - case "$1" in - all) - cmd="all" - ;; - checkout) - cmdcheckout="checkout" - cmd="" - ;; - diff) - cmddiff="diff" - cmd="" - ;; - deploy) - # deploy the built binary. - shift - if [ $# -lt 1 ]; then - echo "deploy <dir> missing" - errcode=1 - cmd="help" - break - fi - cmddeploy="deploy" - DEPLOYDIRNAME="$1" - ;; - deploydir) - # default directory for deployment. - shift - if [ $# -lt 1 ]; then - echo "deploydir <dir> missing" - errcode=1 - cmd="help" - break - fi - deploydir="$1" - ;; - test) - cmdtest="test" - cmd="" - ;; - setenv) - # set environment variable - shift - eval $1="$2" - export $1 - shift - ;; - setenvN) - # set environment variable with $1 values - # e.g., setenvN 3 x a b c is same as setenv x="a b c". - # a kludge now--the extra single quotes are needed - # else eval complains. - shift - envN=$1 - shift - envname=$1 - envalue= - while test $envN -gt 0; do - shift - envalue="$envalue $1" - envN=`expr $envN - 1` - done - eval $envname="'$envalue'" - export $envname - ;; - srcdir) - #use srcdir option for test - srcdir="yes" - ;; - srcdirname) - shift - if [ $# -lt 1 ]; then - echo "srcdirname <dir> missing" - errcode=1 - cmd="help" - break - fi - SRCDIRNAME="$1" - ;; - release) - cmdrel="release" - cmd="" - ;; - clean | distclean) - cmdclean="$1" - cmd="" - ;; - help) - cmd="help" - break - ;; - echo) - set -x - break - ;; - zlib) - shift - if [ $# -lt 1 ]; then - echo "ZLIB information missing" - errcode=1 - cmd="help" - break - fi - ZLIB="$1" - ;; - releasedir) - shift - if [ $# -lt 1 ]; then - echo "Release directory name missing" - errcode=1 - cmd="help" - break - fi - ReleaseDir="$1" - ;; - check-vfd) - CHECKVAL=check-vfd - ;; - yodconfigure) - YODCONFIGURE=yes - ;; - --*) - OP_CONFIGURE="$OP_CONFIGURE $1" - ;; - op-configure) - shift - if [ $# -lt 1 ]; then - echo "op-configure option missing" - errcode=1 - cmd="help" - break - fi - OP_CONFIGURE="$OP_CONFIGURE $1" - ;; - *) - echo "Unkown option $1" - errcode=1 - cmd="help" - break - ;; - esac - shift -done - -# Dump environment variables after option parsing -echo ===Dumping environment variables after option parsing === -printenv | sort -echo ===Done Dumping environment variables after option parsing === - -if [ "$cmd" = help ]; then - set - - cat <<EOF -Usage: $PROGNAME [all] [checkout] [diff] [test] [srcdir] [release] [help] - [clean] [distclean] [echo] [deploy <dir>] [deploydir <dir>] - [zlib <zlib_path>] [releasedir <dir>] [srcdirname <dir>] [check-vfd] - [op-configure <option>] [--<option>] - all: Run all commands (checkout, test & release) - [Default is all] - checkout: Run source checkout - diff: Run diff on current and previous versions. Exit 0 if - no significant differences are found. Otherwise, non-zero. - deploy: deploy binary to directory <dir> - deploydir: use <dir> as the default directory for deployment - test: Run test - release: Run release - clean: Run make clean - distclean:Run make distclean - echo: Turn on echo mode (set -x) - setenv <name> <value>: - Set environment variable <name> to <value>. - setenvN <N> <name> <value> ...: - Set environment variable with <N> values. - E.g., setenvN 3 x a b c is same as setenv x="a b c". - srcdir: Use srcdir option (does not imply other commands) - "snapshot srcdir" is equivalent to "snapshot srcdir all" - "snapshot srcdir checkout" is equivalent to "snapshot checkout" - srcdirname <dir>: - Use <dir> as the srcdir testing directory if srcdir is choosen. - If <dir> starts with '-', it is append to the default name - E.g., "snapshot srcdir srcdirname -xx" uses hostname-xx - [Default is hostname] - help: Print this message - echo: Turn on shell echo - zlib <zlib_path>: - Use <zlib_path> as the ZLIB locations - [Default is $ZLIB_default] - releasedir <dir>: - Use <dir> as the release directory - [Default is $ReleaseDir_default] - check-vfd: - Run make check-vfd instead of just make check. - op-configure <option>: - Pass <option> to the configure command - E.g., "snapshot op-configure --enable-parallel" - configures for parallel mode - --<option>: - Pass --<option> to the configure command - E.g., "snapshot --enable-parallel" - configures for parallel mode -EOF - exit $errcode -fi - -# Setup the proper configure option (--with-zlib) to use zlib library -# provide ZLIB is non-empty. -ZLIB=${ZLIB:+"--with-zlib="$ZLIB} -if [ -n "$YODCONFIGURE" ]; then - cp configure configure.yod - bin/yodconfigure configure.yod - CONFIGURE="./configure.yod" -else - CONFIGURE="./configure" -fi -CONFIGURE="$CONFIGURE $ZLIB $OP_CONFIGURE" - -# Execute the requests -snapshot=yes - -if [ -f bin/snapshot_version ]; then - . bin/snapshot_version -else - H5VERSION=hdf5 -fi - -BASEDIR=${HOME}/snapshots-${H5VERSION} -if [ ! -d ${BASEDIR} ]; then - echo "BASEDIR ($BASEDIR) does not exist" - exit 1 -fi - -CURRENT=${BASEDIR}/current -PREVIOUS=${BASEDIR}/previous -ReleaseDir=${ReleaseDir:=${BASEDIR}/${ReleaseDir_default}} -HOSTNAME=`hostname | cut -f1 -d.` # no domain part -if [ $H5VERSION != hdf5 ]; then - SVNVERSION="hdf5/branches/$H5VERSION" -else - SVNVERSION=hdf5/trunk # use the default (trunk) version -fi - -# Try finding a version of diff that supports the -I option too. -DIFF=diff -for d in `echo $PATH | sed -e 's/:/ /g'` ; do - test -x $d/diff && $d/diff -I XYZ /dev/null /dev/null > /dev/null 2>&1 && - DIFF=$d/diff && break -done - -#============================= -# Run source checkout -#============================= -if [ "$cmd" = "all" -o -n "$cmdcheckout" ]; then - TIMESTAMP "checkout" - # If there is a Makefile in ${CURRENT}, the last test done in it - # has not been distclean'ed. They would interfere with other - # --srcdir build since make considers the files in ${CURRENT} - # take precedence over files in its own build-directory. Run - # a "make distclean" to clean them all out. This is not really - # part of the "checkout" functions but this is the most convenient - # spot to do the distclean. We will also continue the checkout process - # regardless of the return code of distclean. - ( cd ${CURRENT}; test -f Makefile && ${MAKE} distclean) - - SVNROOT=http://svn.hdfgroup.uiuc.edu - # Check out the current version from source repository. - (cd $BASEDIR; svn -q co ${SVNROOT}/${SVNVERSION} current ) || exit 1 -fi # Do source checkout - - -#============================= -# Run Test the HDF5 library -#============================= -if [ "$cmd" = "all" -o -n "$cmdtest" -o -n "$cmddiff" ]; then - TIMESTAMP "diff" - # setup if srcdir is used. - if [ -z "$srcdir" ]; then - TESTDIR=${CURRENT} - else - #create TESTDIR if not exist yet - case "$SRCDIRNAME" in - "") - SRCDIRNAME=$HOSTNAME - ;; - -*) - SRCDIRNAME="$HOSTNAME$SRCDIRNAME" - ;; - esac - TESTDIR=${BASEDIR}/TestDir/${SRCDIRNAME} - test -d ${TESTDIR} || mkdir ${TESTDIR} - fi - # Make sure current version exists and is clean - if [ -d ${TESTDIR} ]; then - (cd ${TESTDIR} && ${MAKE} distclean) - else - errcode=$? - snapshot=no - exit $errcode - fi - - # Compare it with the previous version. Compare only files listed in - # the MANIFEST plus the MANIFEST itself. - if [ -d ${PREVIOUS} ]; then - if (${DIFF} -c ${PREVIOUS}/MANIFEST ${CURRENT}/MANIFEST); then - snapshot=no - for src in `grep '^\.' ${CURRENT}/MANIFEST|expand|cut -f1 -d' '`; do - if ${DIFF} -I H5_VERS_RELEASE -I " released on " \ - -I " currently under development" \ - ${PREVIOUS}/$src ${CURRENT}/$src - then - : #continue - else - snapshot=yes - break - fi - done - fi - fi - - # if diff is choosen, exit 0 if no significant differences are found. - # otherwise, exit 1. This includes cases of other failures. - if [ -n "$cmddiff" ]; then - if [ $snapshot = no ]; then - exit 0 - else - exit 1 - fi - fi - - # Build, run tests and install procedures - if [ "$snapshot" = "yes" ]; then - if (cd ${TESTDIR} && \ - TIMESTAMP "configure" && \ - ${srcdir:+${CURRENT}/}${CONFIGURE} && \ - TIMESTAMP "make" && \ - ${MAKE} && DISKUSAGE \ - TIMESTAMP ${CHECKVAL} && \ - ${MAKE} ${CHECKVAL} && DISKUSAGE \ - TIMESTAMP "install" && \ - ${MAKE} install-all && DISKUSAGE \ - TIMESTAMP "check-install" && \ - ${MAKE} check-install && DISKUSAGE \ - TIMESTAMP "uninstall" && \ - ${MAKE} uninstall-all && DISKUSAGE); then - : - else - errcode=$? - snapshot=no - exit $errcode - fi - fi -fi # Test the HDF5 library - - -#============================= -# Run deployment if requested. -#============================= -if [ -n "$DEPLOYDIRNAME" ]; then - if [ "$snapshot" = "yes" ]; then - TIMESTAMP "deploy" - if (cd ${TESTDIR} && - ${CURRENT}/bin/deploy ${deploydir}/${DEPLOYDIRNAME} && \ - TIMESTAMP "clean" && \ - ${MAKE} clean && \ - TIMESTAMP "check-install prefix=${deploydir}/${DEPLOYDIRNAME}" && \ - ${MAKE} check-install prefix=${deploydir}/${DEPLOYDIRNAME}); then - : #continue - else - errcode=$? - exit $errcode - fi - fi -fi # Deploy - - -#============================= -# Run Release snapshot, update version, and commit to source repository -#============================= -if [ "$cmd" = "all" -o -n "$cmdrel" ]; then - if [ "$snapshot" = "yes" ]; then - TIMESTAMP "release" - (cd ${CURRENT} && ${MAKE} distclean) - ( - # Turn on exit on error in the sub-shell so that it does not - # commit source if errors encounter here. - set -e - cd ${CURRENT} - RELEASE_VERSION="`perl bin/h5vers -v`" - echo "Making snapshot release ($RELEASE_VERSION) to ${ReleaseDir}..." - bin/release -d $ReleaseDir $METHODS - perl bin/h5vers -i - svn -q commit -m "Snapshot $RELEASE_VERSION" - ) - errcode=$? - fi - - # Replace the previous version with the current version. - # Should check if the errcode of the release process but there - # are other failures after release was done (e.g. h5vers or svn failures) - # that should allow the replacement to occure. - rm -rf ${PREVIOUS} - mv ${CURRENT} ${PREVIOUS} -fi #Release snapshot - - -#============================= -# Clean the test area. Default is no clean. -#============================= -if [ -n "$cmdclean" ]; then - TIMESTAMP "clean" - # setup if srcdir is used. - if [ -z "$srcdir" ]; then - TESTDIR=${CURRENT} - else - case "$SRCDIRNAME" in - "") - SRCDIRNAME=$HOSTNAME - ;; - -*) - SRCDIRNAME="$HOSTNAME$SRCDIRNAME" - ;; - esac - TESTDIR=${BASEDIR}/TestDir/${SRCDIRNAME} - fi - # clean it - if (cd ${TESTDIR} && ${MAKE} $cmdclean ) then - : - else - errcode=$? - snapshot=no - exit $errcode - fi -fi # Clean the Test directory - -exit $errcode |