|
HDF5 documents and links Introduction to HDF5 HDF5 User Guide |
And in this document, the
HDF5 Reference Manual
H5 H5A H5D H5E H5F H5G H5I H5P H5R H5S H5T H5Z Tools Datatypes |
HDF5 supports a filter pipeline that provides the capability for standard and customized raw data processing during I/O operations. HDF5 is distributed with a small set of standard filters such as compression (gzip, SZIP, and a shuffling algorithm) and error checking (Fletcher32 checksum). For further flexibility, the library allows a user application to extend the pipeline through the creation and registration of customized filters.
The flexibility of the filter pipeline implementation enables the definition of additional filters by a user application. A filter
H5D_CHUNKED
storage layout), and
The HDF5 library does not support filters for contiguous datasets because of the difficulty of implementing random access for partial I/O. Compact dataset filters are not supported because it would not produce significant results.
Filter identifiers for the filters distributed with the HDF5 Library are as follows:
H5Z_FILTER_DEFLATE | The gzip compression, or deflation, filter |
H5Z_FILTER_SZIP | The SZIP compression filter |
H5Z_FILTER_SHUFFLE | The shuffle algorithm filter |
H5Z_FILTER_FLETCHER32 | The Fletcher32 checksum, or error checking, filter |
See The Dataset Interface (H5D) in the HDF5 User's Guide for further information regarding data compression.
H5Zfilter_avail(H5Z_filter_t filter)
H5Zfilter_avail determines whether the filter
specified in filter is available to the application.
H5Z_filter_t filter |
IN: Filter identifier. See the introduction to this section of the reference manual for a list of valid filter identifiers. |
SUBROUTINE h5zfilter_avail_f(filter, status, hdferr)
IMPLICIT NONE
INTEGER, INTENT(IN) :: filter ! Filter
! Valid values are:
! H5Z_FILTER_DEFLATE_F
! H5Z_FILTER_SHUFFLE_F
! H5Z_FILTER_FLETCHER32_F
! H5Z_FILTER_SZIP_F
LOGICAL, INTENT(OUT) :: status ! Flag indicating whether
! filter is available:
! .TRUE.
! .FALSE.
END SUBROUTINE h5zfilter_avail_f
H5Zget_filter_info(
H5Z_filter_t filter,
unsigned int *filter_config_flags
)
H5Zget_filter_info retrieves information about a filter.
At present, this means that the function retrieves a
filter's configuration flags, indicating whether the filter is
configured to decode data, to encode data, neither, or both.
If filter_config_flags is not set to NULL
prior to the function call, the returned parameter contains a
bit field specifying the available filter configuration.
The configuration flag values can then be determined through
a series of bitwise AND operations, as described below.
Valid filter configuration flags include the following:
|
H5Z_FILTER_CONFIG_ENCODE_ENABLED |
Encoding is enabled for this filter |
H5Z_FILTER_CONFIG_DECODE_ENABLED |
Decoding is enabled for this filter | |
(These flags
are defined in the HDF5 Library source code file
H5Zpublic.h.)
| ||
filter_config_flags and a valid
filter configuration flag will reveal whether
the related configuration option is available.
For example, if the value of
H5Z_FILTER_CONFIG_ENCODE_ENABLED
&
filter_config_flags
0 (zero),
the queried filter is configured to encode data;
if the value is FALSE,
i.e., equal to 0 (zero),
the filter is not so configured.
If a filter is not encode-enabled, the corresponding
H5Pset_* function will return an error if the
filter is added to a dataset creation property list (which is
required if the filter is to be used to encode that dataset).
For example, if the H5Z_FILTER_CONFIG_ENCODE_ENABLED
flag is not returned for the SZIP filter,
H5Z_FILTER_SZIP, a call to H5Pset_szip
will fail.
If a filter is not decode-enabled, the application will not be able to read an existing file encoded with that filter.
This function should be called, and the returned
filter_config_flags analyzed, before calling
any other function, such as H5Pset_szip,
that might require a particular filter configuration.
filter
filter_config_flags
SUBROUTINE h5zget_filter_info_f(filter, config_flags, hdferr)
IMPLICIT NONE
INTEGER, INTENT(IN) :: filter ! Filter, may be one of the
! following:
! H5Z_FILTER_DEFLATE_F
! H5Z_FILTER_SHUFFLE_F
! H5Z_FILTER_FLETCHER32_F
! H5Z_FILTER_SZIP_F
INTEGER, INTENT(OUT) :: config_flags ! Bit field indicating whether
! a filter's encoder and/or
! decoder are available
INTEGER, INTENT(OUT) :: hdferr ! Error code
END SUBROUTINE h5zfilter_avail_f
H5Zregister(const H5Z_class_t filter_class)
)
H5Zregister registers a new filter with the
HDF5 library.
Making a new filter available to an application is a two-step
process. The first step is to write
the three filter callback functions described below:
can_apply_func, set_local_func, and
filter_func.
This call to H5Zregister,
registering the filter with the
library, is the second step.
The can_apply_func and set_local_func
fields can be set to NULL
if they are not required for the filter being registered.
H5Zregister accepts a single parameter,
the filter_class data structure,
which is defined as follows:
typedef struct H5Z_class_t {
H5Z_filter_t filter_id;
const char *comment;
H5Z_can_apply_func_t can_apply_func;
H5Z_set_local_func_t set_local_func;
H5Z_func_t filter_func;
} H5Z_class_t;
filter_id is the identifier for the new filter.
This is a user-defined value between
H5Z_FILTER_RESERVED and H5Z_FILTER_MAX,
both of which are defined in the HDF5 source file
H5Zpublic.h.
comment is used for debugging,
may contain a descriptive name for the filter,
and may be the null pointer.
can_apply_func, described in detail below,
is a user-defined callback function which determines whether
the combination of the dataset creation property list values,
the datatype, and the dataspace represent a valid combination
to apply this filter to.
set_local_func, described in detail below,
is a user-defined callback function which sets any parameters that
are specific to this dataset, based on the combination of the
dataset creation property list values, the datatype, and the
dataspace.
filter_func, described in detail below,
is a user-defined callback function which performs the action
of the filter.
The statistics associated with a filter are not reset by this function; they accumulate over the life of the library.
The callback functions
Before H5Zregister can link a filter into an
application, three callback functions must be defined
as described in the HDF5 Library header file H5Zpublic.h.
The can apply callback function is defined as follows:
H5Z_can_apply_func_t)
(hid_t dcpl_id,
hid_t type_id,
hid_t space_id)
Before a dataset is created, the can apply callbacks for
any filters used in the dataset creation property list are called
with the dataset's dataset creation property list, dcpl_id,
the dataset's datatype, type_id, and
a dataspace describing a chunk, space_id,
(for chunked dataset storage).
This callback must determine whether the combination of the dataset creation property list settings, the datatype, and the dataspace represent a valid combination to which to apply this filter. For example, an invalid combination may involve the filter not operating correctly on certain datatypes, on certain datatype sizes, or on certain sizes of the chunk dataspace.
This callback can be the NULL pointer, in which case
the library will assume that the filter can be applied to a dataset with
any combination of dataset creation property list values, datatypes,
and dataspaces.
The can apply callback function must return a positive value for a valid combination, zero for an invalid combination, and a negative value for an error.
The set local callback function is defined as follows:
H5Z_set_local_func_t)
(hid_t dcpl_id,
hid_t type_id,
hid_t space_id)
After the can apply callbacks are checked for a new dataset,
the set local callback functions for any filters used in the
dataset creation property list are called.
These callbacks receive
dcpl_id, the dataset's private copy of the dataset
creation property list passed in to H5Dcreate
(i.e. not the actual property list passed in to H5Dcreate);
type_id, the datatype identifier passed in to
H5Dcreate,
which is not copied and should not be modified; and
space_id, a dataspace describing the chunk
(for chunked dataset storage), which should also not be modified.
The set local callback must set any filter parameters that are specific to this dataset, based on the combination of the dataset creation property list values, the datatype, and the dataspace. For example, some filters perform different actions based on different datatypes, datatype sizes, numbers of dimensions, or dataspace sizes.
The set local callback may be the NULL pointer,
in which case, the library will assume that there are
no dataset-specific settings for this filter.
The set local callback function must return a non-negative value on success and a negative value for an error.
The filter operation callback function, defining the filter's operation on the data, is defined as follows:
H5Z_func_t)
(unsigned int flags,
size_t cd_nelmts,
const unsigned int cd_values[],
size_t nbytes,
size_t *buf_size,
void **buf)
The parameters flags, cd_nelmts,
and cd_values are the same as for the function
H5Pset_filter.
The one exception is that an additional flag,
H5Z_FLAG_REVERSE, is set when
the filter is called as part of the input pipeline.
The parameter *buf points to the input buffer
which has a size of *buf_size bytes,
nbytes of which are valid data.
The filter should perform the transformation in place if
possible. If the transformation cannot be done in place,
then the filter should allocate a new buffer with
malloc() and assign it to *buf,
assigning the allocated size of that buffer to
*buf_size.
The old buffer should be freed by calling free().
If successful, the filter operation callback function
returns the number of valid bytes of data contained in *buf.
In the case of failure, the return value is 0 (zero)
and all pointer arguments are left unchanged.
H5Zregister interface is substantially revised
from the HDF5 Release 1.4.x series.
The H5Z_class_t struct and
the set local and can apply callback functions
first appeared in HDF5 Release 1.6.
const H5Z_class_t filter_class |
IN: Struct containing filter-definition information. |
H5Zunregister(H5Z_filter_t filter)
H5Zunregister unregisters the filter
specified in filter.
After a call to H5Zunregister, the filter
specified in filter will no longer be
available to the application.
H5Z_filter_t filter |
IN: Identifier of the filter to be unregistered. See the introduction to this section of the reference manual for a list of identifiers for standard filters distributed with the HDF5 Library. |
SUBROUTINE h5zunregister_f(filter, hdferr)
IMPLICIT NONE
INTEGER, INTENT(IN) :: filter ! Filter; one of the possible values:
! H5Z_FILTER_DEFLATE_F
! H5Z_FILTER_SHUFFLE_F
! H5Z_FILTER_FLETCHER32_F
! H5Z_FILTER_SZIP_F
INTEGER, INTENT(OUT) :: hdferr ! Error code
! 0 on success, and -1 on failure
END SUBROUTINE h5zunregister_f
|
HDF5 documents and links Introduction to HDF5 HDF5 User Guide |
And in this document, the
HDF5 Reference Manual
H5 H5A H5D H5E H5F H5G H5I H5P H5R H5S H5T H5Z Tools Datatypes |